Start date jun 6, 2008; What you need to know check out the tools that we use:
Hi, car is a 04 wrx.
Subaru won t start after timing belt replacement. So i turn it back the cam sprocket to the top dead center. I had a mechanic very familiar with the old. Car won't start after timing belt install:
The number one leading cause of a no start after major engine work, or timing belt replacement is the timing it off. Ok, so i was due for a timing belt replacement. It cranks, and sounds normal while cranking, but doesn't even try to.
After swapping them to the correct order the car ran great, just something to check before jumping to the bent valves assumption. Either from using the wrong marks or the belt is just a couple of teeth off by accident. 2005 rx330 162k miles, changed timing belt, vehicle running before, now won't start.
I made sure both cam timing marks were aligned and crankshaft sprocket was aligned. On trying to start, it just cranked and would not start. Fuel pump runs, has spark on front three cylinders have not checked rear yet.
Disconnect battery and discharge vehicle capacitance. Apologies in advance for the extremely long video. Won't start after timing belt replacement.
There is a timing matter in troubleshooting, i think your document says. It turns over, has spark (removed coil pack and grounded plug) and has fuel at the line that feeds the injectors. I ordered up a kit from jackie at annapolis subaru (great service and prices), got the factory service manual and got to work.
Car not starting after timing belt replacement or timing chain replacementif your car does not start after you replaced the timing belt or you replace timing. The timing belt was replaced, but the car still won't start. This is very common with first timers but it also happens with old timers as well.
Coworkers car wont start after head unit install: Security light goes out when key inserted and no codes stored. He has checked the fuel.
After replacing the timing belt, water pump, cam and crank seals, valve cover gaskets the car wont start. Definitely not getting fuel to the cylinder. Like 5 seconds off 8 seconds on.
It's a 2007 2.5 outback with sohc ej25. I just did head gaskets on it and now it won't start. I own the honda service manual for this car, and i followed the instructions exactly.
I have a 2001 honda civic ex with 110,000 miles. Won't start after head gasket job. He replaced the timing idler gear (think that's what it was called) because it had seized up.
Unfortunately that is the most likely outcome of a timing belt breaking on a 97+ subaru engine. Car does not start after timing belt replacement. Car won't start after first start:
Subaru impreza timing belt whistling 1 answer. The engine turned over and it stuttered for a second while i turned the key, but it died as soon as i let go of the key. Last weekend i decided to change the timing belt.
Car does not start after timing belt chain replacementif your car does not start after timing chain or belt replacement, or the car does not start after engi. Had the timing belt replaced at a shop once and the car was returned to me running rough, the mechanic said it was due to the ecu needing to adjust but actually they had replaced the spark plugs in the wrong order. Factory 2.0l turbo powertrain (ej series factory 2.0l turbo) 11:
He also replaced the timing belt. Hi today i was replacing my timing belt and after getting off the timing belt i want to change the cam oil seals and when i try to take off the bolt on one of the cam sprocket, the cam sprocket kind of snap or spring into position. I have checked the timing over and over and find all the marks lining up every time.
Car won't start after timing belt install: This is my third timing belt change but first on this vehicle. Hey guys.recently i changed timing belt, water pump, tensioners, pulleys, belts on my impreza 2006 and after that i started to notice a wierd sound coming from timing belt area , sounds like mini.
Car taking longer to start after timing belt change? Cam dots are pointing up to groove in cover and at the same time the crank pulley is at 0 tdc on the first timing mark turning clockwise. Before trying to start the engine, i bumped it a few times to center the timing belt on the gears.
I have checked for spark from all plugs, wires and coil packs but they are ok. Changed timing belt, won't start now. So i've replaced my timing belt and all marks line up perfectly even after turning by hand 10 times.
After cranking a handful of times, it sounded like the engine was just about to start, but it wouldn't quite take. Verify the timing one more time and then run a compression test to narrow down which cylinders are effected, it's possible that only a few valves were damaged after the break. Factory 2.0l turbo powertrain (ej series factory 2.0l turbo) 22:
Like an idiot, i then tried to see if i could still somehow. Ej22 won't start after timing belt replacement theme. I got excited/distracted and removed one of the idler pulleys before i rotated the engine to line up the crank and cams.
After putting everything back together, i turned the key, and the car wouldn’t start. Car wont start after deck installation! Had to replace water pump on1997 subaru impresa with 2.2 liter, putting on new timing belt (several times),but it wont start and sounds like i have no compression,alligned all timing marks.
Car audio, video & security: Put everything together, after checking timing belt alignment multiple times, and now it wont start. Crank arrow at 12:00, cam marks at 12:00, no start, i replaced the coil, even though i.
He set the timing, but the car won't start. Ok, my timing belt broke, (1996 subaru outback legacy) i replaced the belt and dialed in the timing marks. After half hour of battery down reconnect all and try again.
Give it time to work. It turns over strong and has fuel but won't start. Joined jun 6, 2008 location tacoma, wa tdi 2002 jetta jun 6, 2008 #1 i have a 2002 jetta tdi with 108k that broke a timing belt and the resultant mess with bent valves and etc.
Discussion starter · #1 · feb 5, 2016. Discussion starter · #1 · oct 16, 2015. Disconnect biu connector and spray cleaner on the contacts.
It cranks and tries to sputter and start but just wont do it. Factory 2.0l turbo powertrain (ej series factory 2.0l turbo) 11: